EXTREME SST

접점개선제EXTREME SST

우리는 많은 종류의 접점개선제, 접점부활제를 테스트했다. 그 결과 초고순도, 미크론크기의 은가루를 선택했는데,

현존하는 관련제품들 중에서 가장 뛰어나다고 생각한다.대부분의 접점개선제는 세척제이거나 윤활제이다.

전도체가 아닌 것이다. SST 는 극저온 처리한 초고순도의 은가루로 높은 전도성을 지니며 오디오,

비디오 기기에적용시 극적인 향상이 있다. 고역은 더욱 확장되며, 깨끗해진다.

포커스 역시 더욱 깨끗해지고 향상된다. 중역은 갈라지거나 거칠음이 없이

더욱 투명해지면서 섬세함과 명효함이 향상된다. 저역은 더 강해지고 조여지며 빨라진다.

그리고 사운드스테이지는 더욱 자연스러워진다

WALKER AUDIO 소개
워커오디오의 오디오 철학은 '미니멀리즘'으로 신호경로 상에 어떠한 영향도 가해지지 않도록 하는 것을 의미한다.

원래의 녹음 그리고 원소스에 숨겨진 미소신호까지도 청취자가 들을 수 있도록 하기 위해 워커오디오는

새로운 기술과 제품을 개발한다.

25년간 하이엔드 유저였고, 오디오 설계자이자, 제조자였던 워커오디오 사장 Lloyd Walker는

하이엔더들에게 다음과 같은 질문을 던진다.

당신은 처음 하이엔드를 시작했을 때 느꼈던 감흥을 지금도 느끼고 있습니까? 그렇지 않다면...
왜 새로운 것을 시도하지 않습니까?

EXTREME SST Super Silver Treatment and original SST Super Silver Treatment for all electrical contacts Comes with enough product to treat your system many times over and to share with your friends. Twelve applicators included.

Reveals sonic details and harmonics you’ve been missing. As one reviewer wrote: "leave it to Lloyd (Walker Audio) to improve something you are happy with already" and we did. Extreme SST is easily 20 to 30% better than the original.

While developing SST – Super Silver Treatment, we tested many types of conducting substances and carrier fluids. We chose an ultra-pure, thin, long micron-sized silver flake suspended in an organic fluid for its dielectric characteristics and excellent sound. We believe E-SST/SST are vastly superior compared to any contact treatment on the market today. Most contact treatments on the market are either cleaners or lubricants. They are not conductive. E-SST/SST is highly conductive and must be applied with care according to directions. E-SST/SST will dramatically improve the sound and/or video of any system. The highs will be more extended, cleaner, clearer and better focused. The mid-range will be more transparent with more articulation and detail, yet without harshness or glare. The bass will be stronger, tighter, and quicker. The soundstage will take on a more natural presence. With video systems, the sound improvement will be matched by the improvements to the video. Look for a cleaner, more three-dimensional picture. CAUTION!!! Use at your own risk. Please read the instructions fully before proceeding. E-SST/SST is highly conductive. If you bridge the gap between hot and ground with E-SST/SST, you run the risk of damaging your system. Used as directed. E-SST/SST can be removed by using a clean cotton swab or one of the unused applicators dipped in alcohol, fingernail polish remover, or contact cleaner. Treating Interconnects Use one of the supplied applicators to apply a very small amount of E-SST/SST to the male end of the interconnect. Spread it thinly on about ½ or ¾ of the length of the center pin. Apply E-SST/SST to the outside only of the female end in a thin even coat. Now, plug in your interconnect and listen. On XLR interconnects, apply to male pins only. DO NOT put the applicator into the RCA or you will short it out. Treating Power Cords Apply a thin even coat of E-SST/SST to the male ends only. Cover both sides of the pins about half the length of the pins. On the I.E.C. male end at the component, do the same. Use only a very small amount. Do not over apply. Treating Speaker Cables Apply a thin even coat of E-SST/SST to the contact area of the spades or bananas. Treating Tubes We experienced a big improvement when we applied E-SST/SST to the pins of the tubes in our amplifiers. We suggest cleaning the pins with fine sandpaper in the direction on the pins. Clean with a contact cleaner, then apply a thin, even coat of E-SST/SST to about 2/3 the length of the male pin. Video/Other Uses E-SST/SST works great on video connectors. Apply to the male pins and the outside of female connectors. E-SST/SST also works on fuses and any contact device. Guarantee Of Satisfaction We think you will be amazed. If not, you may return the unused portion within 30 days for a full refund, less shipping.

HOW TO APPLY E-SST/SST Whether you are putting it on audio and video equipment or something else, the same rules apply. It is best to clean the connections with a contact cleaner that leaves no residue. If the contact is corroded, you can lightly sand or scrape it. Then clean it. Apply a very thin (almost transparent) coat of E-SST or SST to the male end of the connector. I’ve been asked which is the male end. For the uninitiated, the male end of a connector is the part that sticks out....think anatomy! Apply to the male end or to the ring connector or to the end of the spark plug that the plug wire goes to. Remember, very thin. More is not better. REMOVE EXCESS If you get too much, use alcohol or contact cleaner to remove it. Take your time and pay close attention. Use E-SST and SST at their own risk. E-SST and SST are very conductive. If you get it across a connection, you can short out your equipment. When applied properly, you will have no problems. In fact, we guarantee you’ll be satisfied with the results or we will refund the purchase price. IF PASTE GETS TOO THICK Over time, E-SST and SST will dry to a thick paste. This is by design so that it does not migrate. In the bottle, if the E-SST and SST thickens, simply add two or three drops of 100% canola oil available at any grocery store and mix with a toothpick. Canola oil has similar properties and will thicken over time, but will not effect the connection or the sound. BREAK-IN PERIOD E-SST/SST will immediately make a significant improvement. It will be even better after eight to ten hours of break-in time for the treated connectors. RECONNECTING/REAPPLYING Before reconnecting, it is beneficial to take a used applicator with the SST wiped off (some will still be embedded in the applicator) and spread over the connector. This will help to distribute the SST that remains on the connector. If you reapply it, make sure there is not excessive SST on the connector. If there is, clean it as directed above before applying more. If you have any questions about how to use this product, call us. NEW USES FOR E-SST/SST Customers are applying E-SST to every electrical connection you could image. (See our Welcome page for more information.) We thought putting it on a hair dryer was bit unusual, but my favorite is the customer who put it on his weed whacker. Lawnmowers and other outdoor equipment with engines can benefit from it. Advanced Uses We've heard from our more adventurous customers, reviewers and manufacturers who have applied E-SST to the inside connections of projectors, computers, and DVD players and we've done this ourselves as well. The results are astounding. This is not recommended for most people, only for qualified electronic technicians. The inside connections are very small and close together and can be fragile. Use a bright light and magnifying glasses to see the connections and a sharp toothpick to apply E-SST. Use only a tiny amount on ¼ to ½ of the pin. And use extreme care to avoid damaging the connectors and/or shorting out your equipment.